Quick Answer: Can Drip Edge Be Installed After Shingles?

Does drip edge go under felt?

At the side, or gabels, of a roof, the drip edge goes over the roofing felt.

At the bottom of the roof, the drip edge goes under the roofing felt..

Do you have to replace drip edge when replacing roof?

Do you need to replace it when replacing the roof? No you do not have to replace it but you should, the old drip edge is most likely “old” looking and dirty from being outside for so long. If you are making the effort to replace you roof, you should replace everything so the entire roofing system looks nice.

How much does drip edge cost?

Drip Edges: $1-$2 per linear foot installed. Inspect and replace drip edges as necessary. Drip edges are added to the roof to direct water into the gutters.

Does sheathing go over fascia?

When sheathing a roof, the first step is to snap a line so that the first row goes on straight. But if you snap it at 40 inches, then the sheathing will not project over the subfascia or true fascia. … Add an inch and a half for subfascia, strike a line.

Can you add drip edge to existing roof?

Because edge drips are meant to be installed on roofs that have yet to be finished, a type F can be the only option available for existing roofs.

What is the difference between drip edge and rake edge?

Drip edge and rake edge are the first parts of the roof system to be installed. They form a long, narrow piece of metal, which is installed along the perimeter your Roof Deck. Drip edge goes along your eaves trough areas and rake edge goes along your gable ends.

Do gutters go under or over drip edge?

It is recommended that gutters are placed under or ‘behind’ the drip edge of your roof. A drip edge refers to a component that hangs over the roof and has an outward projecting lower edge.

Where is drip edge installed on roof?

Drip edge is installed around the whole perimeter of the roof. It is used to hold the underlayments down and create a watertight seal around the edge of the roof. Only the face of the metal is seen and is usually just white one to one and half inch stripe located right under the shingles and above the fascia.

Should drip edge be tight to fascia?

The drip edge should be installed over a piece of 1×2 furring strip so that it stands off from the fascia or rafter tails. If the drip edge is laid right up against the fascia or rafters, then because of surface tension, the water runs right up against the fascia and underneath the soffit.

Do you need drip edge on gable ends?

Drip edges also help prevent shingles at the end of a roof from cracking, sagging, and becoming limp. Drip edges can also be installed on the gable ends of a roof. They add a clean, trimmed look to a roof while preventing water from entering into undesirable areas.

Should shingles be flush with drip edge?

Shingles should be installed over the drip edge a minimum of 3/8” (9 mm) at both the eave edge and the rake edge. If the drip edge extends… out from the rakes and eaves (typically called DL Style or D Type), the shingles may be installed flush with the drip edge.

Can you replace drip edge without removing shingles?

The drip edge is often replaced when new shingles are installed, but it can be replaced at any time. Asphalt roof shingles can become brittle in cold weather, so wait until a warm (but not hot) day to remove and replace eave stripping.

How should drip edge be installed?

Install roof drip edge along the eaves, add underlayment, then place drip edge along the gable end. The best way is to install the roof drip edge only along the eaves first, then place ice-and-water barrier (in the snowbelt) or felt paper (underlayment) over the drip edge.

How far should drip edge be from fascia?

2 inchesCode requires that the drip edge extend at least 2 inches onto the roof from the fascia board. This drip edge extends much farther. Nailing along the eaves should be spaced at no more than 12 inches on-center.

Do I need a drip edge on rake edge?

It’s important to understand that drip edge installation is different for eaves and rakes. After your roof deck has been prepared, and before you install underlayment, you need to install drip edges at the eaves. You install drip edges on the rakes after you install the underlayment.

Can drip edge be painted?

Yes you can paint the aluminum drip edge and it hold up very well. Just be sure it is clean and paint it with a good exterior acrylic primer and finish with a exterior acrylic semi-gloss house paint.

What color drip edge should I use?

Well, first let’s start with the drip edge. If your home’s trim and fascia are white, it is recommended you select a white drip edge for seamless blending of elements throughout. If your home has more pops of brown, similar to the home displayed in the photo to the right, you may want to choose a brown drip edge.

How do you install drip edge under existing shingles?

Make sure the outer edge extends over the gutter. If it doesn’t, pull the drip edge out slightly from under the shingles. Secure the drip edge with roofing cement. Apply a continuous bead of cement along the top of the drip edge, then press down on the shingle.

How do you calculate drip edge?

The drip edge metal is only used at the bottom edge of roofs – near the gutters. Measure the length and add 10% to find how much drip edge you will need.